Netlink 1001 Telco Rack - 1001R14P/RUI
- Supports V.35, Ethernet Networking
- Data Transfer Speeds up to
- Remote Management over SNMP 1, SNMP, HTTP
When users require higher density solutions, a rack system becomes more economical. The NetLink Model 1001 rack system consists of a 2U-high chassis that can be mounted in any standard 19-inch wide telco rack. The Model 1001 chassis supports up to 16 modem modules and a single AC or DC power supply, or dual-redundant AC or DC power supplies.
The rack shown above is a fully-configured NetLink Model 1001 rack system containing 13 modems, a network management module, and two power supply modules that fill the 18 front rack slots. Equipment/network interface modules that fill the rear slots of the rack chassis connect to the front modules through a midplane bus that extends the width of the rack.
Nearly all of the electrical and physical interfaces, from Ethernet to V.35, are available as I/O modules. Dual redundant AC or DC power supplies can be installed in the rack system to help avoid catastrophic failures caused by power fluctuations or outages.
The NetLink rack system enables users to configure, control, and perform diagnostics via SNMP or HTTP. To manage a rack system, the operator need only install a NetLink Management Module (Model 1001MC), connect a workstation to its Ethernet port, and launch a standard Web browser (i.e., Netscape Navigator or Internet Explorer). Now, any operator can manage any NetLink rack card or standalone modems from a local PC or via the Internet.
The Model 1001 rack system can have one or two 90, 264, VAC or -12/-24/-48 VDC power supplies installed in any combination. Each power supply can support a fully-loaded rack configured with any combination of front modem modules and rear I/O cards. If two power supplies are installed, they automatically self-configure for dual-redundant, load-sharing operation. In dual-redundant configuration, each power supply shares 50% of the load.
The 1001R14P/RUI is a red, 2U, 14-slot rack with (2) two 90 - 260VAC power supplies operating in a load-sharing, dual-redundant mode.
Netlink 1001 Telco Rack - 1001R14P/RUI
|
Connectivity
|
|
|
# Ports
|
14
|
|
Protocols
|
|
|
Networking Protocol
|
V.35
|
|
Networking Protocol
|
Ethernet
|
|
Remote Management Protocol
|
SNMP 1
|
|
Remote Management Protocol
|
SNMP
|
|
Remote Management Protocol
|
HTTP
|
|
Switching Protocol
|
Ethernet
|
|
Actual Weight
|
0.70 lb(s)
|
|
Compatibility Notes
|
Features & Benefits
High-density rack system supports up to 16 modems in a 2U-high, 19-inch wide rack-mount chassis with integral AC/DC power supply
Configurable input / output modules support all serial, voice / fax, Ethernet and G.703 DTE interfaces.
The NetLink rack system can expand to 320 modems in a standard 40U-high rack system.
Integrated SNMP and HTTP management system
Automatic load-sharing, dual-redundant AC and DC power supplies
Network management via SNMP or HTTP
Dual-redundant AC and DC power supplies
Great Modularity & Interface Functionality
|
|
Contents
|
Unit, hardware, documentation
|
|
Ports/Connectors
|
Interface:
10Base-T Ethernet via RJ-45
Terminal Interface via RS-232
|
|
Power Notes
|
(2) two 90 - 260VAC power supplies operating in a load-sharing, dual-redundant mode.
48 VDC Power
Input Voltage: 42–60 VDC
Input Current: 2.2A nominal
Surge Protection: to 75 VDC
AC Power
Input Voltage: 90–264 VAC
Input Frequency: 50 / 60Hz
Input Current: 1.8 A RMS
Surge Protection: to 300 VAC
|
|
Returns Policy
|
This product is subject to our return policy. Please see our complete return policy for details.
|
|
Warranty - Labor
|
1 Year
|
|
Warranty - Parts
|
1 Year
|
Netlink 1001 Telco Rack - 1001R14P/RUI
http://www.pcconnection.com/IPA/Shop/Product/Detail.htm?sku=5526183#BVSecondaryCustomerRatings