Cisco 7200 Series 2-Port 10/100 Auto-Sensing Fast Ethernet Input/Output Controller - C7200-I/O-2FE/E=
The Cisco 7200 Series 2-Port 10/100 Auto-Sensing Fast Ethernet Input/Output Controller provides high-speed LAN connectivity without using a port adapter slot. With Gigabit Ethernet interconnectivity, interface flexibility through the use of industry-standard GBICs, increased 7200 port density, improved price/performance ratio, and additional Flash memory, the 7200 Series 2-Port has everything you want.
Cisco 7200 Series 2-Port 10/100 Auto-Sensing Fast Ethernet Input/Output Controller - C7200-I/O-2FE/E=
|
General
|
|
|
Adapter Type
|
Control processor
|
|
Performance
|
|
|
Data Transfer Rate
|
100 MB/s
|
|
Actual Weight
|
2.40 lb(s)
|
|
Contents
|
Unit, documentation.
|
|
Memory Notes
|
Flash Memory: 8 MB
PCMCIA Flash disk supported: 48 MB (default) expandable up to 128 MB
|
|
Physical Dimensions
|
1.3"h x 13.4"w x 7.2"d
|
|
Ports/Connectors
|
Auxiliary ports: 1
Console ports: 1
Ethernet ports: 2 (FE / E autosensing)
Fast Ethernet ports: 2 (FE / E autosensing)
PCMCIA slots: 2
Connectors: both are RJ-45
Single-port, full-duplex Gigabit Ethernet port
Interface flexibility by using industry-standard GBICs, including the following:
1000BASE-SX multimode, compliant with IEEE 802.3z specifications
1000BASE-LX / LH compliant with IEEE 802.3z specifications
1000BASE-ZX
GBIC connector: 20-pin AMP SCA-2 equivalent
Supports 802.1q virtual LAN (VLAN) and Inter-Switch Link (ISL) as software selectable features.
Fast Ethernet Ports (two on C7200-I/O-2FE / E)
Autosensing 10 / 100 Fast Ethernet ports
Connector: RJ-45
MAC with full-duplex operation and flow control.
Hardware address filtering on received frames of up to 128 address entries.
802.3x flow control
Ethernet encapsulation formats: Ethernet V2
802.2 SAP
802.2 SNAP
Supports 802.1q VLAN and ISL as software-selectable features.
Port Adapter compatibility—In some cases, the LAN ports on the
I/O controllers (C7200-I/O-GE+E and C7200-I/O-2FE / E) share the protocol control information (PCI) bus bandwidth with the port adapter ports in all odd-numbered slots on the 7200 series chassis. This condition occurs when the NPE-225, NPE-400, or NSE-1 processors are used. It does not apply to the NPE-G1. Configuration Guidelines for the Port Adapters and I/O controllers with more detailed information can be found at:
link
|
|
Returns Policy
|
Due to manufacturer restrictions, all sales on this item are final.
|
|
System Requirements
|
Hardware Requirements:
Chassis compatibility—The C7200-I/O, C7200-I/O-GE+E, and the C7200-I/O-2FE / E are supported on the Cisco 7200 Series VXR chassis. The C7200-I/O is also supported on the Cisco 7200 Series (non-VXR) chassis.
Software Requirements:
The C7200-I/O-GE+E and the C7200-I/O-2FE / E are supported in Cisco IOS Software releases 12.1(3A)E5, 12.1(5)T1, and 12.0(14)S2 or later.
Processor Compatibility—With one exception, all Cisco 7200 Series configurations with chassis and processor require an I/O controller. The NPE-G1 does not require an I/O controller because it includes built-in console and auxiliary ports, as well as a slot for Flash memory. However, the Cisco NPE-G1 Network Processing Engine and I/O controllers are compatible as shown in Table 7 and the I/O controller may be ordered as an option.
Cisco 7200 Series I/O Controller Compatibility with Network Processors
Network Processing Engine (NPE): NPE-225 and above (see note below)*
Network Services Engine (NSE): NSE-1
*The C7200-I/O-2FE / E I/O controller only operates with this version of the NPE-225: board label 73-3453-05 rev. A0 or higher, or faceplate label 800-05418-03 rev. A0 or higher. To check for the correct NPE-225 version in software, use the show c7200 command. Under CPU EEPROM, look for Hardware Revision 1.3 or higher.
|
|
Warranty - Labor
|
N/A
|
|
Warranty - Parts
|
N/A
|
Cisco 7200 Series 2-Port 10/100 Auto-Sensing Fast Ethernet Input/Output Controller - C7200-I/O-2FE/E=
http://www.pcconnection.com/IPA/Shop/Product/Detail.htm?sku=225924#BVSecondaryCustomerRatings